Page 124 - Seaward Safety | Supplying Signage Solutions

Information Boards * All Boards can be tailored
to suit requirements

YOUR YOUR OPERATION INSTRUCTION
LOGO LOGO
HERE HERE LIFEBOAT DAVIT
EMBARKATION WINCH LAUNCHING
BRAKE
LEVER
1. Able bodied personnel board lifeboat immediately. Casualties on stretchers are passed inboard 1. CONNECT PAINTER LINE.
and secured. All passengers put on seatbelts. Helmsman starts the engine.
2. EMBARKATION.
2. The last person to board reconfirms that launching area is clear.
3. RELEASE OR MAKE SURE LASHINGS RELEASES AUTOMATICALLY.
3. All doors and portholes are verified as being closed. 4. LOWER BOAT WITH REMOTE CONTROL WIRE OR BY LIFTING THE WINCH BRAKE LEVER.
5. WITH BOAT ON WATER, RELEASE WINCH WIRE BEFORE PAINTER LINE.
REMOTE
LAUNCHING THE LIFEBOAT Installation for ship-type Installation for platform CONTROL NORMAL OPERATION - RECOVERY
WIRE
1. Make sure that all lifeboat lashings are removed before launching. 1. CONNECT PAINTER LINE AND THEN WINCH WIRE.
2. RAISE BOAT UP TO THE BOARDING PLATFORM BY PUSHING “HOIST” - BUTTON EITHER
2. Pull the control wire in top of the hatch. Pulling down on the control wire lifts the brake and starts
the descent. Releasing it applies the brake and stops the descent. ON REMOTE CONTROL BOX OR THE STARTER CABINET.
3. The winch has a two-speed lowering system with a hydraulic speed controller. Both the low speed, 3. USE THE HAND CRANK TO HOIST THE LAST 0.5m AND BRING THE BOAT TO ITS CORRECT
which should be used during turn-out of the davit and the high speed used for the descent is fixed POSITION. REF. OPERATION AND MAINTENANCE MANUAL.
by the hydraulic speed controller and cannot be adjusted by the remote control wire.
4. CONNECT OR CHECK LASHING IS SECURED.
During turn-out of the davit a gentle pull should be applied to the remote control wire and the winch
will operate at low speed. When the lowering blocks/hook links leaves the davit head, pull harder on
the wire and the high speed mode will be activated. For more detailed instruction see also the
winch manual. IN CASE OF DEAD SHIP OPERATION - RECOVERY
4. The boat should be allowed to descend to the water at the automatically controlled speed and 1. PLACE HAND CRANK IN CRANK HOUSE.
splash down. This frees the falls for easy release. 2. RAISE THE BOAT BY USING HAND CRANK.
PIN LASHING
NOTE:
RUN LAUNCHING: ALWAYS CONNECT PAINTER LINE
HOIST
E.M. STOP BOAT ON WATER: DISCONNECT MAIN WINCH WIRE LINE BEFORE PAINTER LINE
REMOTE CONTROL
SP-2314 - 420mm x 297mm SP-2314-ALT1 - 420mm x 297mm
Lifeboat Launch Instructions. Lifeboat Launch Instructions.
YOUR SURVIVAL CRAFT YOUR FACILITY NAME
LOGO LOGO
HERE INSTRUCTIONS HERE LIFEBOAT STATUS
SURVIVAL CRAFT SC85F MAX POB 60 PERSONS
1 FULLY OPERATIONAL
Centrifugal
brake
2 OUT OF SERVICE
Survival craft
max POB 60 Entry Entry
door door
Centrifugal
Centrifugal
Centrifugal
brake
3 FULLY OPERATIONAL
brake
brake
EMBARKATION
1. Before entering lifeboat, Coxswain to check area below lifeboat is clear of obstructions, the rudder and propeller are intact, the wind and wave direction and all
electrical plugs have been disconnected.
2. Once Coxswains has completed all lifeboat checks, started the engine and the OIM has given permission to board all personnel are to enter the lifeboat distributing
themselves evenly throughout the lifeboat beginning aft then moving forward. All personnel are to fasten seat belts. Any casualties are to be loaded last.
3. With all personnel in position and doors closed the Coxswain will report readiness for launching to Control and Command. The Oim will give permission for launching. OUT OF SERVICE
LAUNCHING 4
1. The coxswain will delegate one person to pull down on the winch remote control wire to release the holding brake.
2. The lifeboat will lower to the water, descent is controlled by the centrifugal braking mechanism in the winch.
3. Once lifeboat is waterborne release the hook mechanism and proceed to safe area paying the brake release cable through the hole in the canopy.
SP-6154 - 420mm x 297mm SP-9508 - 297mm x 210mm
Survival Craft Instructions. Lifeboat Status Board.
YOUR RESCUE BOAT YOUR NORSAFE JYN100
LOGO LOGO
HERE LAUNCHING PROCEDURE HERE LAUNCH INSTRUCTIONS
1 EMBARKATION 2 SAFETY BELTS 3 CLOSE DOORS 4 START COMPRESSED AIR SYSTEM 5 START ENGINE
OPEN THE ACCESS HATCH DOOR AND FASTEN SAFETY BELTS IMMEDIATELY CLOSE HATCHES AND ACCESS HATCH OPEN ALL AIR CYLINDER VALVES (1) AND AIR RELEASE LIFEBOAT CAPTAIN STARTS
VALVE (2). OPERATE THE HANDLE OF THE PRESSURE
AFTER TAKING SEATS.
THE ENGINE AT IDLING RPM
DOORS.
SECURE DOOR IN OPEN POSITION.
2 REGULATOR (3) SO AS TO KEEP THE INDICATOR OF NEUTRAL CLUTCH. SEE
1 CREW MEMBERS EMBARK QUICKLY. DIFFERENTIAL PRESSURE GAUGE (4) APPROX 0.8Mpa NOW ENGINE INSTRUCTION MANUAL.
REMAIN CALM AND TAKE SEATS.
SUPPLIED WITH AIR. SEE SEPERATE INSTRUCTION.
RELEASE TURN OUT OPEN OPEN CLOSE 3 4 1 45 LTRS (20 MPa)
GRIPES DAVIT CLOSE 2 STOP OFF ON START
OPERATING INSTRUCTIONS OF A TOTALLY ENCLOSED LIFEBOAT
BOAT LOWERING
6
AND WATERBORNE
3 4 CAUTION LIFEBOAT CAPTAIN PULLS AND MAINTAINS
STEADY PULL ON THE LOWERING CONTROL
LOWER TO START LOOK FOR AND GATHER ROPE UNTIL WATERBORNE AND FALLS
ARE RELEASED.
WATER ENGINE OTHER SURVIVORS.
OPEN LOCKER AND READ PULL
SURVIVAL MANUAL.
5 11 COMMUNICATION 10 FRESH AIR SUPPLY 9 FULL SPEED RELEASE 8 SPRINKLER VALVE 7 DISENGAGEMENT
WHEN ALREADY AWAY FROM WHEN OUTSIDE THE DANGER ZONE LIFEBOAT CAPTAIN PUSH THROTTLE MOVE SPRINKLER INLET VALVE LEVER 1. WHEN WATERBORNE REMOVE SAFETY PIN AND OPERATE THE LEVER TO DISCONNECT
FALLS FROM THE BOAT. SEE DETAILED HOOK INSTRUCTION.
RELEASE THE DANGER ZONE PROCEED OPEN THE VENTILATORS FOR FRESH CONTROL LEVER AHEAD AND STEER LOCATED IN FRONT OF THE ENGINE. 2. PULL THE PAINTER RELEASE TO DISCONNECT PAINTER FROM THE BOAT.
AIR SUPPLY.
AWAY ON A DESIGNATED COMPASS
FOLLOWING ACTION:
SEE SEPERATE INSTRUCTION.
1.
COURSE.
1. SETUP UP SART AND OPERATE
FALLS 2. DISTRESS SIGNALS.
SETUP UP RADAR REFLECTOR.
2.
PULL
SP-9621 - 420mm x 297mm SP-4055 - 420mm x 297mm
Rescue Boat Launching Procedure. Norsafe JYN100 Launch Instructions.
124